蘭炭煤氣發電機組使用的時候，如何防止蘭炭煤氣發電機組出現漏油、作為發電機廠家，讓小編帶大家共同了解一下防止蘭炭煤氣發電機組漏油的技巧!

　　How to prevent oil leakage of Lantan gas generator set when using it? As a generator manufacturer, let me take you to understand the techniques to prevent oil leakage of Lantan gas generator set!

　　1、粘補膠治漏法。油箱、水箱、油管、水管因決裂或砂眼、氣孔等引起小滲漏，可用粘補膠涂改在清洗潔凈的破害處即可。

　　1. Adhesive repair method for treating leaks. Oil tanks, water tanks, oil pipes, and water pipes may experience minor leaks due to rupture or sand holes, air holes, etc. They can be repaired with adhesive and cleaned to prevent damage.

　　2、加墊治漏法。蘭炭煤氣發電機組里的油管接頭防漏墊圈處漏油，可在防漏墊圈的兩端加一層雙面潤滑的薄塑料墊，用力擰緊即可防漏。

　　2. Add padding to treat leaks. The oil pipe joint leak proof gasket in the Lantan gas generator set leaks oil. A thin plastic pad with double-sided lubrication can be added to both ends of the leak proof gasket and tightened firmly to prevent leakage.

　　3、以抽治漏法。蘭炭煤氣發電機組的油箱底殼、氣紅蘇、齒輪室養、曲軸箱后蕭等多處紙墊滲漏時，若紙墊無缺、接合面清潔，可在紙墊雙面林上一層黃油，擰緊螺栓即可防漏;如換新紙墊，把新紙墊放在柴油中浸泡10分

　　3. Using the method of extracting and treating leaks. When there are leaks in the oil tank bottom shell, gas red Su, gear room maintenance, crankcase rear Xiao and other paper pads of the Lantan gas generator set, if the paper pads are intact and the joint surface is clean, a layer of butter can be applied to both sides of the paper pads, and the bolts can be tightened to prevent leakage; If replacing the paper pad, soak it in diesel for 10 minutes

　　鐘后取出擦凈，在接合面上抹一層黃油再裝上。

　　Take out the bell and wipe it clean. Apply a layer of butter on the joint surface before putting it back on.

　　4、漆片液治漏法。柴油機油箱、水箱、曲軸箱等接縫處滲漏，可將漆片在酒精里浸泡后，把漆片液涂改在清洗潔凈的接縫外即可。5、厭膠治漏法。柴油機上的通氣螺栓、雙頭螺栓等處出現滲漏時，可用厭氧膠涂改在清洗潔凈的螺栓螺紋處或螺孔里，能很快固化構成薄膜，填充零件空隙;此法用于柴油機高壓油管接頭螺紋處治漏效果更好。

　　4. Lacquer slice liquid leak treatment method. If there is leakage at the joints of the diesel engine fuel tank, water tank, crankcase, etc., the paint can be soaked in alcohol and the paint liquid can be applied outside the cleaned joints. 5. The method of using adhesive to treat leaks. When there is leakage at the ventilation bolts, double headed bolts, etc. on the diesel engine, anaerobic adhesive can be used to modify the cleaned bolt threads or screw holes, which can quickly solidify into a thin film and fill the gaps in the parts; This method is more effective in treating leaks in high-pressure oil pipe joints of diesel engines.

　　6、液態密封膠治漏法。柴油機上出現固體墊困缺陷而構成的界面性滲漏和破壞性滲漏時，用液態密封膠涂改在清洗潔凈的固體墊園結合面上，固化后構成均勻、穩定、連續黏附的可剝性薄膜墊園，可防滲漏。

　　6. Liquid sealant leakage treatment method. When there is interface leakage and destructive leakage caused by solid gasket entrapment defects on diesel engines, liquid sealant is used to modify the joint surface of the cleaned solid gasket. After curing, it forms a uniform, stable, and continuously adhered peelable film gasket, which can prevent leakage.

　　7、只度康年膠治漏法、柴油機的軸與軸棄、軸承與軸承座、煙與煙瘁、自緊油、填料等處滲漏時，可用尺磨康復膠涂改在清洗潔凈的協作件磨損部位，固化后構成耐磨、機械強度較高的薄膜層，再進行機加工康復零件的幾何形狀和協作精度，可解決滲漏

　　7. When leakage occurs in areas such as shafts and shafts of diesel engines, bearings and bearing seats, smoke and exhaust, self tightening oil, fillers, etc., only the Kangnian adhesive treatment method can be used. A ruler can be used to grind and repair the adhesive to clean the worn parts of the cooperative parts. After curing, a wear-resistant and mechanically strong thin film layer can be formed, and then the geometric shape and cooperation accuracy of the parts can be repaired by machining, which can solve the problem of leakage

　　本文由   蘭炭煤氣發電機組    友情奉獻.更多有關的知識請點擊  http://www.miaotoo.net/   真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is a friendly contribution from the Lantan Gas Generator Unit For more related knowledge, please click http://www.miaotoo.net/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.